code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)
STEP2 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The
device LED's blink in sequence (TV-VCR-AUX-CBL-TV)
STEP3 Release the buttons when the desired device button is blinking (the device LED will
then remain lit).
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED
STEP4 Point the remote control toward the
*Tip : You can verify that you selected the
equipment and enter the three-digit
correct code by pressing the
code number assigned to your
[POWER] button. The equipment
brand from the code tables.
should either turn on or turn off.
*Tip : The equipment will turn off when the
STEP5 Press the [SELECT] button to store
correct three-digit code number has
the code. The device LED will blink
been entered. You can verify that you
twice to confirm that the code
selected the correct code by pressing
has been stored.
the [POWER] button. The equipment
should turn on or turn off.
C. To Find the Three Digit Code
*Note : If there is more than one three-digit
Number That was Stored in the
number listed for your brand, try
one code number at a time until
your equipment turns off.
STEP1 Press the [SELECT] button and
[MUTE] button simultaneously for 3
STEP5 Store the three-digit code number
seconds. The device LED's blink in
by pressing the [SELECT] button.
sequence (TV-VCR-AUX-CBL-TV)
The device LED will blink twice to
confirm that the code has been
STEP2 Release the buttons when the
desired device button is blinking (the
device LED will then remain lit).
*Note : Try all the functions on the remote
control. If any of the functions do
*Tip : The device LED will stay lit for 20
not work as they should, repeat
seconds. The next step must be
from Step 2 using the next three-
entered while the LED is on.
digit code number from the same
brand list.
STEP3 Press the [INFO] button.
The device LED will blink number of
times indicating the number of each
B. Auto Search Method.
digit of the code number. Each digit
If the three-digit code numbers assigned to
is separated by a 1 second interval
your brand do not turn off your equipment or
of the LED being turned off.
the code tables do not list your brand, you
Example : One blink, three blinks and eight
can use the Auto Search Method to find the
blinks with an interval of 1
correct three-digit code number for your
second of LED being turned off,
equipment by the following steps:
indicates the code number 138.
STEP1 Turn on the equipment you wish to
*Note : Ten blinks is equal to the number 0.
program. (TV, VCR, DVD or AUX)
STEP2 Press the [SELECT] button and
D. Programming a Second TV to AUX
[MUTE] button simultaneously for 3
seconds. The device LED's blink in
sequence (TV-VCR-AUX-CBL-TV)
STEP1 Turn on the TV you wish to program.
STEP3 Release the buttons when the
STEP2 Press the [SELECT] button and
desired device button is blinking
[MUTE] button simultaneously for 3
(the device LED will then remain lit).
seconds. The device LED's blink in
*Tip : The device LED will stay lit for 20
sequence (TV-VCR-AUX-CBL-TV)
seconds. The next step must be
STEP3 Release the buttons when the [AUX]
entered while LED is on.
device LED is blinking (the [AUX]
STEP4 Press the [CH+] or [CH-] button one
device LED will then remain lit).
at a time or keep it pressed. The
STEP4 Hold down the [MUTE] button. The
remote will emit a series of power
device LED's will begin blinking in
on/off commands. Release the
sequence again. Release the
[CH+] or [CH-] button as soon as the
[MUTE] button when the [TV] device
equipment turns off.
LED is blinking (the [TV] device LED
will then remain lit).
*Tip : The device LED will stay lit for 20
STEP2 Release the buttons when the [TV]
seconds. The next step must be
device LED is blinking (the [TV]
entered while the LED is on.
device LED will then remain lit).
*Tip : The device LED will stay lit for 20
STEP5 Point the remote control toward the
seconds. The next step must be
equipment and enter the three-digit
code number assigned to your TV
entered while the LED is on.
brand from the code tables.
STEP3 Press the [VOL-] button.
*Tip : The equipment will turn off when the
STEP4 Press the [TV] button.
correct three-digit code number has
The device LED will blink twice to
been entered. You can verify that you
selected the correct code by pressing
the [POWER] button. The equipment
To return to original state:
should turn on or turn off.
If you wish to restore the CABLE channel
STEP6 Store the three-digit code number
control in TV mode, repeat the above steps by
by pressing the [SELECT] button.
pressing [CBL] in STEP4.
The [AUX] device LED will blink
twice to confirm that the code has
been stored.
G. Programming Volume Control.
E. Programming the VOD Button.
By following the steps below, the you can
This is designed to program the VOD button
program the volume controls (Volume UP,
so that it can access video on demand with
Volume Down and MUTE) from one device
one button press.
to operate in another device mode. The
default volume control settings on the
The VOD button is factory defaulted to Ch 999 .
To re-program to a different channel:
remote control is as follows:
STEP1 Press the [CBL] button.
STEP2 Press the [VOD] button and the
[SELECT] button simultaneously for
If you wish to store the CBL volume control
3 seconds. The [CBL] button will
in CBL mode, use the following steps.
turn on for 20 seconds.
STEP1 Press the [SELECT] button and
STEP3 Press the Numbers of the desired
[MUTE] button simultaneously for 3
channel to become the new Macro.
seconds. The device LED's blink in
sequence (TV-VCR-AUX-CBL-TV)
STEP4 Press the [CH+] button to save the
new Macro you stored.
STEP2 Release the buttons when the
The [CBL] button will blink twice to
[CBL] device LED is blinking (the
[CBL] device LED will then remain
F. Programming Channel Control.
*Tip : The device LED will stay lit for 20
By following the steps below, the you can
seconds. The next step must be
program the channel controls (channel UP,
entered while the LED is on.
and channel DOWN) from one device to
operate in another device mode.
STEP3 Press the [VOL+] button.
The default channel control settings on the
remote control is as follows:
STEP4 Press the [CBL] button. The device
LED will blink twice to confirm the
programming.
To return to original state:
If you wish to store the TV channel control in
If you wish to restore the TV volume control in
TV mode, use the following steps.
CBL mode, repeat the above steps by
STEP1 Press the [SELECT] button and
pressing [TV] in STEP4.
[MUTE] button simultaneously for 3
seconds. The device LED's blink in
sequence (TV-VCR-AUX-CBL-TV)
Our app is now available on Google Play
